SamyGO - User contributions [en]

The K Series Wiki

2018-06-16T20:08:49Z

Szt:

*'''[[Ex-Link Cable for J/K/M/Q/N/QN Series]]'''
*'''[[Enter developer mode on Tizen TV`s]]'''
'''Rooting K series TV (T-JZM* and T-HKMFK* firmwares up to versions 1169.2. Currently untested on T-JZL6*, but boundaries would be same, if working at all.)'''

For now, rooting technique of K series TV is only available to users that donated to our community.

* [https://forum.samygo.tv/viewtopic.php?f=70&t=12260 Related topic on the forum...]

UNDER CONSTRUCTION

To be updated...

The J Series Wiki

2018-06-16T20:08:19Z

Szt:

Here will be the information about Tizen OS and J series soon.

This is a misc. collection of currently known information. It will be organized better over time.

'''J Series Forum:''' http://forum.samygo.tv/viewforum.php?f=83&sid=bb1391eb2668cb6e2d3c3d793dc557b0

'''Service Menu'''

Be VERY careful once in the service menu. Do not try to navigate using LEFT and RIGHT because that changes values. Only navigate through menu items with UP and DOWN.

With TV powered on (requires remote with FACTORY key): [INFO] [FACTORY] (starts service menu with "Advanced" visible but it has no sub-menu)

With TV powered off: [MUTE] [1] [8] [2] on American models and [INFO] [MENU] [MUTE] [POWER] on European models.

'''Console output'''
*'''[[Ex-Link Cable for J/K/M/Q/N/QN Series]]'''

Ex Link Port - 115,200 N,8,1

RS-232 Jack setting:

UART = no input/output

Debug = system logging output (MUCH more verbose when "Serial Log On/Off" set to ON, which requires a power cycle to take effect)

Logic = no input/output

FANET = no input/output

'''OTN Support Disable (Firmware Upgrades)'''

OTN support cannot be disabled in the service menu. It must be disabled by blocking access to the upgrade servers at the network level.

'''Rooting J series TV (T-HK* fw up to 1480)'''

For now, rooting technique of J series TV is only available to users that donated to our community.

* [https://forum.samygo.tv/viewtopic.php?f=70&p=99518 Related topic on the forum...]

'''Rooting J series TV (T-NT14MJ* fw up to ????)'''

H rooting method can be used (because TV's with T-NT14MJ* fw is renamed H series):

* [https://forum.samygo.tv/viewtopic.php?f=70&t=9622 Related topic on the forum...]

The M/Q Series Wiki

2018-06-16T20:07:42Z

Szt:

*'''[[Ex-Link Cable for J/K/M/Q/N/QN Series]]'''
*'''[[Enter developer mode on Tizen TV`s]]'''

*UNDER CONSTRUCTION

To be updated...

Ex-Link Cable for J/K/M/Q/N/QN Series

2018-06-16T20:06:13Z

Szt: Szt moved page Ex-Link Cable for J/K/M/Q/N/NQ Series to Ex-Link Cable for J/K/M/Q/N/QN Series

== Wired Ex-Link cable ==
[[File:JU7100-inputs-side-large.jpg|200px|thumb|right|JU7100]]On some J/K-series TV and on M/Q series Tv`s, Ex-Link port is located on the separate 3.5mm jack labelled as "EX-LINK".
On Q series Ex-Link port is located on bottom of OneConect box, next to CI slot.

In this case, you need to make Ex-link cable by connecting JACK male to the USB-COM adapter ({{red|'''not''' TTL/LVTTL}}) as shown below.

[[File:Img.jpg|500px]]

Or you can use regular COM port, if your PC have it, but in this case you have to connect pins in reverse order (from left to right) as shown below. You need 2, 3 and 5 pin.

If your PC does not have COM port (like many pc`s nowadays), you can use cheap '''[https://www.aliexpress.com/wholesale?ltype=wholesale&d=y&origin=y&isViewCP=y&spm=2114.01010208.8.42.NMUo8j&initiative_id=QRW_20170607091544&SearchText=usb+rs232+db9+cable&productId=32672290017&blanktest=0&tc=af USB to RS232 COM Port Serial PDA 9 pin DB9 Cable Adapter ]'''.

[[File:Db9-pinout.png]]
== USB Ex-Link cable ==
Tested on UE32K5502 TV. On other TV models there may be differences.
===Service menu===
First you need enable USB Ex-Link for your TV in service menu. Try sequence <code>Info -> Menu -> Mute -> Power</code> or <code>Info -> Settings -> Mute -> Power</code> when TV turned off (may not work). Other way - if you have root, you can start service menu with command <code>launch_app org.tizen.factory</code>.

In service menu, go to Control -> Sub Option, change <code>RS-232 Jack - Debug</code>, <code>EXT Link Support - ON</code>, <code>USB Serial - ON</code>. You can also set <code>Watchdog - OFF</code>. On the other TV model, these options can be in another place of the service menu.

[[File:K_SERVICE_USB.JPG|500px]]
===Cable===
My TV have USB ExLink UART with 0V/3.3V voltage level. {{red|'''Not''' RS232}} which can have -25V/+25V voltage level - see https://www.electronics-notes.com/articles/connectivity/serial-data-communications/rs232-signal-voltage-levels.php

Maybe other models will be with RS232, so it's better to check voltage before plugging something in Ex-Link enabled USB port. You accept that you do everything at YOUR OWN RISK.

After making changes in the service menu, one of USB port will stop work like USB (TV will not detect flash drive plugged in it) - this USB port you need to use. Yon need some USB-UART 3.3V - like Nokia data cable CA-42/DKU-5. Connect UART wires to USB wires:
TV USB GND to GND UART
TV USB DATA- to RX UART
[[File:USB.jpg|500px]][[File:UART_USB.jpg|500px]]

== Enable Debug mode in service menu ==
todo
== Start the terminal ==
===Linux PC===
On a Linux PC, install 'cu' (call up) tool from the ''uucp'' package and run
<pre>cu -l /dev/ttyUSB0 -s 115200</pre>
 
===Windows PC===
On Windows, we recommend the free terminal application [http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html Putty] or [http://realterm.sourceforge.net/ RealTerm] ([http://sourceforge.net/projects/realterm/ download]). But [http://www.hilgraeve.com/hyperterminal/ HyperTerminal] is also very nice, but not free.

After you have started PuTTY, follow the steps in the screen shots below. 
[[File:ExLinkPuttySettings1.png|300px]][[File:ExLinkPuttySettings2.png|300px]]
[[File:ExLinkPutty3.png|600px]]

Ex-Link Cable for J/K/M/Q/N/NQ Series

2018-06-16T20:06:13Z

Szt: Szt moved page Ex-Link Cable for J/K/M/Q/N/NQ Series to Ex-Link Cable for J/K/M/Q/N/QN Series

#REDIRECT [[Ex-Link Cable for J/K/M/Q/N/QN Series]]

Ex-Link Cable for J/K/M/Q/N/QN Series

2018-06-16T20:01:57Z

Szt: Szt moved page Ex-Link Cable for J/K/M/Q Series to Ex-Link Cable for J/K/M/Q/N/NQ Series

Ex-Link Cable for J/K/M/Q Series

2018-06-16T20:01:57Z

Szt: Szt moved page Ex-Link Cable for J/K/M/Q Series to Ex-Link Cable for J/K/M/Q/N/NQ Series

#REDIRECT [[Ex-Link Cable for J/K/M/Q/N/NQ Series]]

Ex-Link Cable for J/K/M/Q/N/QN Series

2018-06-16T19:12:28Z

Szt: DATA+ - TX connection removed.

File:UART USB.jpg

2018-06-16T19:11:25Z

Szt: Szt uploaded a new version of File:UART USB.jpg

Rooting H series TV

2018-06-08T08:36:23Z

Szt:

* [https://forum.samygo.tv/viewtopic.php?f=75&t=10919 "Skype replacement" root] - This method is for OLD FIRMWARES (T-MST14 <= 2130, T-GFPx < 1290, T-NT14U < 1050, all T-GFS).
* [https://forum.samygo.tv/viewtopic.php?f=70&t=9622 "Network" root (FW<=Oct.2015, no T-GFS)] - Should be suitable for (at least): T-NT14U<1050, T-GFPxDEUC<1290 T-MST14<2790, NT14M < ??? and NT14MJDEUC < ???? (10/12/2017) firmwares.
If your current firmware is "out of range", check [https://forum.samygo.tv/viewtopic.php?f=75&t=10137 here] and [https://forum.samygo.tv/viewtopic.php?f=75&t=11379 there] for possible downgrade.

The K Series Wiki

2018-04-14T00:55:33Z

Szt:

*'''[[Ex-Link Cable for J/K/M/Q Series]]'''
*'''[[Enter developer mode on Tizen TV`s]]'''
'''Rooting K series TV (T-JZM* and T-HKMFK* firmwares up to versions 1169.2. Currently untested on T-JZL6*, but boundaries would be same, if working at all.)'''

For now, rooting technique of K series TV is only available to users that donated to our community.

* [https://forum.samygo.tv/viewtopic.php?f=70&t=12260 Related topic on the forum...]

UNDER CONSTRUCTION

To be updated...

The K Series Wiki

2018-04-14T00:50:54Z

Szt:

*'''[[Ex-Link Cable for J/K/M/Q Series]]'''
*'''[[Enter developer mode on Tizen TV`s]]'''
'''Rooting K series TV (T-JZ* and T-HK* fws up to 1169)'''

For now, rooting technique of K series TV is only available to users that donated to our community.

* [https://forum.samygo.tv/viewtopic.php?f=70&t=12260 Related topic on the forum...]

UNDER CONSTRUCTION

To be updated...

The K Series Wiki

2018-04-14T00:49:57Z

Szt:

Ex-Link Cable for J/K/M/Q/N/QN Series

2018-04-13T22:09:50Z

Szt:

== Wired Ex-Link cable ==
[[File:JU7100-inputs-side-large.jpg|200px|thumb|right|JU7100]]On some J/K-series TV and on M/Q series Tv`s, Ex-Link port is located on the separate 3.5mm jack labelled as "EX-LINK".
On Q series Ex-Link port is located on bottom of OneConect box, next to CI slot.

In this case, you need to make Ex-link cable by connecting JACK male to the USB-COM adapter ({{red|'''not''' TTL/LVTTL}}) as shown below.

[[File:Img.jpg|500px]]

Or you can use regular COM port, if your PC have it, but in this case you have to connect pins in reverse order (from left to right) as shown below. You need 2, 3 and 5 pin.

If your PC does not have COM port (like many pc`s nowadays), you can use cheap '''[https://www.aliexpress.com/wholesale?ltype=wholesale&d=y&origin=y&isViewCP=y&spm=2114.01010208.8.42.NMUo8j&initiative_id=QRW_20170607091544&SearchText=usb+rs232+db9+cable&productId=32672290017&blanktest=0&tc=af USB to RS232 COM Port Serial PDA 9 pin DB9 Cable Adapter ]'''.

[[File:Db9-pinout.png]]
== USB Ex-Link cable ==
Tested on UE32K5502 TV. On other TV models there may be differences.
===Service menu===
First you need enable USB Ex-Link for your TV in service menu. Try sequence <code>Info -> Menu -> Mute -> Power</code> or <code>Info -> Settings -> Mute -> Power</code> when TV turned off (may not work). Other way - if you have root, you can start service menu with command <code>launch_app org.tizen.factory</code>.

In service menu, go to Control -> Sub Option, change <code>RS-232 Jack - Debug</code>, <code>EXT Link Support - ON</code>, <code>USB Serial - ON</code>. You can also set <code>Watchdog - OFF</code>. On the other TV model, these options can be in another place of the service menu.

[[File:K_SERVICE_USB.JPG|500px]]
===Cable===
My TV have USB ExLink UART with 0V/3.3V voltage level. {{red|'''Not''' RS232}} which can have -25V/+25V voltage level - see https://www.electronics-notes.com/articles/connectivity/serial-data-communications/rs232-signal-voltage-levels.php

Maybe other models will be with RS232, so it's better to check voltage before plugging something in Ex-Link enabled USB port. You accept that you do everything at YOUR OWN RISK.

After making changes in the service menu, one of USB port will stop work like USB (TV will not detect flash drive plugged in it) - this USB port you need to use. Yon need some USB-UART 3.3V - like Nokia data cable CA-42/DKU-5. Connect UART wires to USB wires:
TV USB GND to GND UART
TV USB DATA- to RX UART
TV USB DATA+ to TX UART
[[File:USB.jpg|500px]][[File:UART_USB.jpg|500px]]

== Enable Debug mode in service menu ==
todo
== Start the terminal ==
===Linux PC===
On a Linux PC, install 'cu' (call up) tool from the ''uucp'' package and run
<pre>cu -l /dev/ttyUSB0 -s 115200</pre>
 
===Windows PC===
On Windows, we recommend the free terminal application [http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html Putty] or [http://realterm.sourceforge.net/ RealTerm] ([http://sourceforge.net/projects/realterm/ download]). But [http://www.hilgraeve.com/hyperterminal/ HyperTerminal] is also very nice, but not free.

After you have started PuTTY, follow the steps in the screen shots below. 
[[File:ExLinkPuttySettings1.png|300px]][[File:ExLinkPuttySettings2.png|300px]]
[[File:ExLinkPutty3.png|600px]]

Ex-Link Cable for J/K/M/Q/N/QN Series

2018-04-13T22:00:45Z

Szt: USB Ex-Link

== Wired Ex-Link cable ==
[[File:JU7100-inputs-side-large.jpg|200px|thumb|right|JU7100]]On some J/K-series TV and on M/Q series Tv`s, Ex-Link port is located on the separate 3.5mm jack labelled as "EX-LINK".
On Q series Ex-Link port is located on bottom of OneConect box, next to CI slot.

In this case, you need to make Ex-link cable by connecting JACK male to the USB-COM adapter ({{red|'''not''' TTL/LVTTL}}) as shown below.

[[File:Img.jpg|500px]]

Or you can use regular COM port, if your PC have it, but in this case you have to connect pins in reverse order (from left to right) as shown below. You need 2, 3 and 5 pin.

If your PC does not have COM port (like many pc`s nowadays), you can use cheap '''[https://www.aliexpress.com/wholesale?ltype=wholesale&d=y&origin=y&isViewCP=y&spm=2114.01010208.8.42.NMUo8j&initiative_id=QRW_20170607091544&SearchText=usb+rs232+db9+cable&productId=32672290017&blanktest=0&tc=af USB to RS232 COM Port Serial PDA 9 pin DB9 Cable Adapter ]'''.

[[File:Db9-pinout.png]]
== USB Ex-Link cable ==
Tested on UE32K5502 TV. On other TV models there may be differences.
===Service menu===
First you need enable USB Ex-Link for your TV in service menu. Try sequence <code>Info -> Menu -> Mute -> Power</code> or <code>Info -> Settings -> Mute -> Power</code> when TV turned off (may not work). Other way - if you have root, you can start service menu with command <code>launch_app org.tizen.factory</code>.

In service menu, go to Control -> Sub Option, change <code>RS-232 Jack - Debug</code>, <code>EXT Link Support - ON</code>, <code>USB Serial - ON</code>. You can also set <code>Watchdog - OFF</code>. On the other TV model, these options can be in another place of the service menu.

[[File:K_SERVICE_USB.JPG|500px]]
===Cable===
My TV have USB ExLink UART with 0V/3.3V voltage level. {{red|'''Not''' RS232}} which can have -25V/+25V voltage level - see https://www.electronics-notes.com/articles/connectivity/serial-data-communications/rs232-signal-voltage-levels.php

Maybe other models will be with RS232, so it's better to check voltage before plugging something in Ex-Link enabled USB port. You accept that you do everything at YOUR OWN RISK.

After making changes in the service menu, one of USB port will stop work like USB (TV will not detect flash drive plugged in it) - this USB port you need to use. Connect UART wires to USB wires:
TV USB GND to GND UART
TV USB DATA- to RX UART
TV USB DATA+ to TX UART
[[File:USB.jpg|500px]][[File:UART_USB.jpg|500px]]

== Enable Debug mode in service menu ==
todo
== Start the terminal ==
===Linux PC===
On a Linux PC, install 'cu' (call up) tool from the ''uucp'' package and run
<pre>cu -l /dev/ttyUSB0 -s 115200</pre>
 
===Windows PC===
On Windows, we recommend the free terminal application [http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html Putty] or [http://realterm.sourceforge.net/ RealTerm] ([http://sourceforge.net/projects/realterm/ download]). But [http://www.hilgraeve.com/hyperterminal/ HyperTerminal] is also very nice, but not free.

After you have started PuTTY, follow the steps in the screen shots below. 
[[File:ExLinkPuttySettings1.png|300px]][[File:ExLinkPuttySettings2.png|300px]]
[[File:ExLinkPutty3.png|600px]]

File:UART USB.jpg

2018-04-13T21:38:37Z

Szt:

File:USB.jpg

2018-04-13T21:03:14Z

Szt: USB Standard A

USB Standard A

File:J SERVICE USB.JPG

2018-04-13T20:28:49Z

Szt: Szt moved page File:J SERVICE USB.JPG to File:K SERVICE USB.JPG

#REDIRECT [[File:K SERVICE USB.JPG]]

File:K SERVICE USB.JPG

2018-04-13T20:28:48Z

Szt: Szt moved page File:J SERVICE USB.JPG to File:K SERVICE USB.JPG

Setting for UE32K5502 in service menu to enable USB Ex-Link

File:K SERVICE USB.JPG

2018-04-13T20:25:27Z

Szt: Setting for UE32K5502 in service menu to enable USB Ex-Link

Setting for UE32K5502 in service menu to enable USB Ex-Link

Rooting H series TV

2018-04-13T20:02:18Z

Szt: Links updated

* [https://forum.samygo.tv/viewtopic.php?f=75&t=10919 "Skype replacement" root] - Should be suitable for (at least): T-NT14U<1050, T-GFPxDEUC<1290 T-MST14<2790, NT14M < ??? and NT14MJDEUC < ???? (10/12/2017) firmwares.
* [https://forum.samygo.tv/viewtopic.php?f=70&t=9622 "Network" root (FW<=Oct.2015, no T-GFS)] - This method is for OLD FIRMWARES (T-MST14 <= 2130, T-GFPx < 1290, T-NT14U < 1050, all T-GFS).
If your current firmware is "out of range", check [https://forum.samygo.tv/viewtopic.php?f=75&t=10137 here] and [https://forum.samygo.tv/viewtopic.php?f=75&t=11379 there] for possible downgrade.

The J Series Wiki

2017-12-20T17:48:10Z

Szt: T-NT14MJ* rooting

Here will be the information about Tizen OS and J series soon.

This is a misc. collection of currently known information. It will be organized better over time.

'''J Series Forum:''' http://forum.samygo.tv/viewforum.php?f=83&sid=bb1391eb2668cb6e2d3c3d793dc557b0

'''Service Menu'''

Be VERY careful once in the service menu. Do not try to navigate using LEFT and RIGHT because that changes values. Only navigate through menu items with UP and DOWN.

With TV powered on (requires remote with FACTORY key): [INFO] [FACTORY] (starts service menu with "Advanced" visible but it has no sub-menu)

With TV powered off: [MUTE] [1] [8] [2] on American models and [INFO] [MENU] [MUTE] [POWER] on European models.

'''Console output'''
*'''[[Ex-Link Cable for J/K/M/Q Series]]'''

Ex Link Port - 115,200 N,8,1

RS-232 Jack setting:

UART = no input/output

Debug = system logging output (MUCH more verbose when "Serial Log On/Off" set to ON, which requires a power cycle to take effect)

Logic = no input/output

FANET = no input/output

'''OTN Support Disable (Firmware Upgrades)'''

OTN support cannot be disabled in the service menu. It must be disabled by blocking access to the upgrade servers at the network level.

'''Rooting J series TV (T-HK* fw up to 1480)'''

For now, rooting technique of J series TV is only available to users that donated to our community.

* [https://forum.samygo.tv/viewtopic.php?f=70&p=99518 Related topic on the forum...]

'''Rooting J series TV (T-NT14MJ* fw up to ????)'''

H rooting method can be used (because TV's with T-NT14MJ* fw is renamed H series):

* [https://forum.samygo.tv/viewtopic.php?f=70&t=9622 Related topic on the forum...]

The J Series Wiki

2017-04-17T15:04:15Z

Szt: Rooting J series TV

Here will be the information about Tizen OS and J series soon.

This is a misc. collection of currently known information. It will be organized better over time.

'''J Series Forum:''' http://forum.samygo.tv/viewforum.php?f=83&sid=bb1391eb2668cb6e2d3c3d793dc557b0

'''Service Menu'''

Be VERY careful once in the service menu. Do not try to navigate using LEFT and RIGHT because that changes values. Only navigate through menu items with UP and DOWN.

With TV powered on (requires remote with FACTORY key): [INFO] [FACTORY] (starts service menu with "Advanced" visible but it has no sub-menu)

With TV powered off: [MUTE] [1] [8] [2] on American models and [INFO] [MENU] [MUTE] [POWER] on European models.

'''Console output'''
*'''[[Ex-Link Cable for J/K Series]]'''
Ex Link Port - 115,200 N,8,1

RS-232 Jack setting:

UART = no input/output

Debug = system logging output (MUCH more verbose when "Serial Log On/Off" set to ON, which requires a power cycle to take effect)

Logic = no input/output

FANET = no input/output

'''OTN Support Disable (Firmware Upgrades)'''

OTN support cannot be disabled in the service menu. It must be disabled by blocking access to the upgrade servers at the network level.

'''Rooting J series TV (T-HK* fw up to 1480)'''

For now, rooting technique of J series TV is only available to users that donated to our community.

* [https://forum.samygo.tv/viewtopic.php?f=70&p=99518 Related topic on the forum...]

Ex-Link Cable for J/K/M/Q/N/QN Series

2016-09-06T13:15:58Z

Szt: newline

== Wired ExLink cable ==
[[File:JU7100-inputs-side-large.jpg|200px|thumb|right|JU7100]]On some J/K-series TV, Ex-Link port is located on the separate 3.5mm jack labelled as "EX-LINK".

In this case, you need to make Ex-link cable by connecting JACK male to the USB-COM adapter(not TTL/LVTTL) as shown below.

[[File:Img.jpg|500px]]

Or you can use regular COM port, if your PC have it, but in this case you have to connect pins in reverse order (from left to right) as shown below. You need 2, 3 and 5 pin.

[[File:Db9-pinout.png]]
== Enable Debug mode in service menu ==
todo
== Start the terminal ==
===Linux PC===
On a Linux PC, install 'cu' (call up) tool from the ''uucp'' package and run
<pre>cu -l /dev/ttyUSB0 -s 115200</pre>
 
===Windows PC===
On Windows, we recommend the free terminal application [http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html Putty] or [http://realterm.sourceforge.net/ RealTerm] ([http://sourceforge.net/projects/realterm/ download]). But [http://www.hilgraeve.com/hyperterminal/ HyperTerminal] is also very nice, but not free.

After you have started PuTTY, follow the steps in the screen shots below. 
[[File:ExLinkPuttySettings1.png|300px]][[File:ExLinkPuttySettings2.png|300px]]
[[File:ExLinkPutty3.png|600px]]

The K Series Wiki

2016-09-01T05:53:22Z

Szt:

*'''[[Ex-Link Cable for J/K Series]]'''
*UNDER CONSTRUCTION

To be updated...

The J Series Wiki

2016-09-01T05:51:52Z

Szt:

Here will be the information about Tizen OS and J series soon.

This is a misc. collection of currently known information. It will be organized better over time.

'''J Series Forum:''' http://forum.samygo.tv/viewforum.php?f=83&sid=bb1391eb2668cb6e2d3c3d793dc557b0

'''Service Menu'''

Be VERY careful once in the service menu. Do not try to navigate using LEFT and RIGHT because that changes values. Only navigate through menu items with UP and DOWN.

With TV powered on (requires remote with FACTORY key): [INFO] [FACTORY] (starts service menu with "Advanced" visible but it has no sub-menu)

With TV powered off: [MUTE] [1] [8] [2] on American models and [INFO] [MENU] [MUTE] [POWER] on European models.

'''Console output'''
*'''[[Ex-Link Cable for J/K Series]]'''
Ex Link Port - 115,200 N,8,1

RS-232 Jack setting:

UART = no input/output

Debug = system logging output (MUCH more verbose when "Serial Log On/Off" set to ON, which requires a power cycle to take effect)

Logic = no input/output

FANET = no input/output

'''OTN Support Disable (Firmware Upgrades)'''

OTN support cannot be disabled in the service menu. It must be disabled by blocking access to the upgrade servers at the network level.

Top Debug Menu: TDM

2016-09-01T05:51:40Z

Szt:

The hidden menu, accessible using special cable, so called ExLink. 

Required steps to get to TOP debug menu:
==TV service menu settings==
*In service menu, '''enable Debug mode''' for the RS232 port:
:With TV switched off, press the following sequence on the remote: 
:*UE,LE models:'''[INFO] [MENU] [MUTE] [POWER]''' 
:*UN,UA models:'''[MUTE] 1 8 2 [POWER]''' 
*Enter the '''Control''' menu and set the value of the '''RS232 mode''' to '''Debug'''.
*Once you're back to the main Service menu, you will have to power off the TV for normal operation.
Notice that your TV will reset RS232 mode back to UART when you install another firmware (no matter if it's older or newer).
==ExLink cable==
*[[Enable Serial Console on non CI+ Devices |Ex-Link Cable for B-Series]]
*[[Ex-Link Cable for C/D Series | Ex-Link Cable for C/D/E Series and BD players]]
*[[Ex-Link Cable for J/K Series]]
====Terminal Connection Parameters ====
*Use following connection parameters with your terminal-client ( e.g. [http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html putty], Kermit, Hyper Therminal or ZOC Terminal ):
Baudrate: '''115200'''
Data bits: '''8'''
Parity: '''none'''
Stop bits: '''1'''
Flow Control: '''none'''

== Start the terminal ==
===Linux PC===
On a Linux PC, install 'cu' (call up) tool from the ''uucp'' package and run
<pre>cu -l /dev/ttyUSB0 -s 115200</pre>
===Windows PC===
On a Windows PC, use Hyper Terminal or [http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html Putty]. 
After you have started PuTTY, follow the steps in the screen shots below. 
[[File:ExLinkPuttySettings1.png|300px]][[File:ExLinkPuttySettings2.png|300px]]
[[File:ExLinkPutty3.png|600px]]

==Console unlock and TDM codes==
First code unlocks console, the second is the key for TDM. NB you can`t see anything on terminal window until you unlock console. Means, you input first code blindy and just after you press ENTER, you will see what you type (e.g. code for TDM).
===B series===
*[[Enable_Serial_Console_on_non_CI%2B_Devices#Debug_Menu_.28On_CI.2B_Devices_Too.29 | TDM on B series]]
debug
1198282
===C series===
10041004
20089999
===D series===
*ARM:
23331003
20089999
*Mstar:
1198282
20089999
*BD
20102011
20089999
===E & ES series===
*ARM (Series 7 & 8):
20102011
20089999
*MStar (Series 5 & 6):
1198282
20089999
*BD:
20102011
20089999
===F series ===
*Series 6
20139120
TDM: 20089999

*Series 8
20133697
TDM: 20089999

===H series ===
20149144
TDM: unknown yet

===J series ===
??
TDM: unknown yet

===K series ===
20165299
TDM: 20089999
== [ TOP Debug Menu ] ==
===Navigation principles===
choosing the number of submenu you get deeper in to chosen submenu. 
If you need change values, usually you will see this:
Input Down(0)/Up(1)/Down100(2)/Up100(3)/Exit(99) > :
Means: 
Every input of '''0''' you get netxt value of this setting. 
Every input of '''1''' shows the value before. 
After the right value is chosen, confirm your selected value with input of '''99'''. This saves setting and exits current submenu.

AFAIK the 2 and 3 make same as 0 and 1.

===Examples===
As example: how to get in to Factory menu (Service menu, but accessible from ExLink cable). 
TV: LE40B653T5W, but on other series the TDM is very similar...

====================================
[ TOP Debug Menu]
------------------------------------
1 : SubSystem Print On/Off
2 : Platform Print Setting
3 : TD Print Setting
4 : Performance Print Setting
5 : Sdal Print Setting
6 : Sdal Trace Setting
10 : Factory Debug
11 : TD Debug
12 : SubSystem DBG
20 : Performance File Write
21 : Louvre Print Setting
22 : JavaMW Print Setting
30 : Auto Lock DBG
------------------------------------
50 : ROSE Debug
60 : MediaLink Debug
70 : Jade Debug
====================================
99 : Exit
====================================
DBG> : 10

====================================
[ SsExeFactoryBase Debug Menu]
------------------------------------
1 : Factory.dat Loading Debug
2 : Hidden Menu Status
3 : GetItem Test
4 : Get SpecialItem Data
5 : Print SpecialItem Number
6 : Each Store Area, Version Clear
7 : Set SpecialItem Data
8 : Default Data Update Test
9 : Display & Excute Factory Menu
====================================
99 : Exit
====================================
DBG> : 9

====================================
[ SsExeFactoryBase Main Menu]
SOURCE_TYPE_DTV1 RESOLUTION_576I
------------------------------------
[0] Option
[1] ADC/WB
[2] Control
[3] SVC
[4] Advanced
[5] FBE3
[6] WB Movie
[7] EPA Standard
[8] CH_VDEC
[9] YC_Delay
[10] AR_ADC
[11] CH_DP
[12] NR
[13] Sharpness
[14] Sharpness_LNA
[15] CE DIMMING
[16] LNA_Plus
[17] Tuner Status
[18] FRC
[19] PQ Others
[20] EEPROM RESET
[21] ...
[22] TC905x7
[23] DDR Margin
====================================
99 : Exit
====================================
Select Menu :2

====================================
[ Control]
SOURCE_TYPE_DTV1 RESOLUTION_576I
------------------------------------
[0] EDID
[1] Sub Option
[2] PDP Option
[3] Hotel Option
[4] Shop Option
[5] Asia Option
[6] SOUND
[7] Config Option
[8] Test Pattern
====================================
99 : Exit
====================================
Select Menu : 7

====================================
[ Config Option]
SOURCE_TYPE_DTV1 RESOLUTION_576I
------------------------------------
[0] Num of ATV
[1] Num of DTV
[2] Num of AV
[3] Num of SVIDEO
[4] Num of COMP
[5] Num of HDMI
[6] Num of PC
[7] Num of SCART
[8] Num of DVI
[9] Num of OPTICAL Link
[10] Num of MEDIA
[11] Num of PANEL KEY
[12] Num of USB Port
[13] MFT Offset
[14] Select LCD/PDP
[15] HDMI/DVI SEL
[16] Indicator Led
[17] Wall Mount
[18] Chelsea HV Flip
[19] Num Of Display
[20] HDMI AV MUTE TIME
[21] DVI/HDMI SOUND
[22] HDMI HOT PLUG
[23] HOTPLUG SWITCHING
[24] HOT PLUG OFF HOLD TIME
[25] HDMI FLT CNT SIG
[26] HDMI FLT CNT LOS
[27] UNSTABLE BAN CNT
[28] HDMI Err Cnt
[29] HDMI ROBIN
[30] HDMI Callback
[31] HDMI CTS Thld
[32] HDMI CTS Cnt1
[33] TMDS_EQ2_Boost
[34] TMDS_EQ2_Gain
[35] TMDS_PLL_Loop
[36] TMDS_CPREG_BLEED
[37] HDMI EQ
[38] HDMI Switch
[39] TTX Group Delay
[40] DVI SET TIME
[41] Woofer_Type
[42] Tuner Lock Count
[43] SIL2165 FW128
====================================
99 : Exit
====================================
Select Menu :

If you need to change some option in service menu, you don`t need to enter this from remote control. Use ExLink instead ;) 
<To be updated>

Top Debug Menu: TDM

2016-09-01T05:47:52Z

Szt: Ex-Link Cable for J/K_Series

The hidden menu, accessible using special cable, so called ExLink. 

Required steps to get to TOP debug menu:
==TV service menu settings==
*In service menu, '''enable Debug mode''' for the RS232 port:
:With TV switched off, press the following sequence on the remote: 
:*UE,LE models:'''[INFO] [MENU] [MUTE] [POWER]''' 
:*UN,UA models:'''[MUTE] 1 8 2 [POWER]''' 
*Enter the '''Control''' menu and set the value of the '''RS232 mode''' to '''Debug'''.
*Once you're back to the main Service menu, you will have to power off the TV for normal operation.
Notice that your TV will reset RS232 mode back to UART when you install another firmware (no matter if it's older or newer).
==ExLink cable==
*[[Enable Serial Console on non CI+ Devices |Ex-Link Cable for B-Series]]
*[[Ex-Link Cable for C/D Series | Ex-Link Cable for C/D/E Series and BD players]]
*[[Ex-Link Cable for J/K_Series]]
====Terminal Connection Parameters ====
*Use following connection parameters with your terminal-client ( e.g. [http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html putty], Kermit, Hyper Therminal or ZOC Terminal ):
Baudrate: '''115200'''
Data bits: '''8'''
Parity: '''none'''
Stop bits: '''1'''
Flow Control: '''none'''

== Start the terminal ==
===Linux PC===
On a Linux PC, install 'cu' (call up) tool from the ''uucp'' package and run
<pre>cu -l /dev/ttyUSB0 -s 115200</pre>
===Windows PC===
On a Windows PC, use Hyper Terminal or [http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html Putty]. 
After you have started PuTTY, follow the steps in the screen shots below. 
[[File:ExLinkPuttySettings1.png|300px]][[File:ExLinkPuttySettings2.png|300px]]
[[File:ExLinkPutty3.png|600px]]

==Console unlock and TDM codes==
First code unlocks console, the second is the key for TDM. NB you can`t see anything on terminal window until you unlock console. Means, you input first code blindy and just after you press ENTER, you will see what you type (e.g. code for TDM).
===B series===
*[[Enable_Serial_Console_on_non_CI%2B_Devices#Debug_Menu_.28On_CI.2B_Devices_Too.29 | TDM on B series]]
debug
1198282
===C series===
10041004
20089999
===D series===
*ARM:
23331003
20089999
*Mstar:
1198282
20089999
*BD
20102011
20089999
===E & ES series===
*ARM (Series 7 & 8):
20102011
20089999
*MStar (Series 5 & 6):
1198282
20089999
*BD:
20102011
20089999
===F series ===
*Series 6
20139120
TDM: 20089999

*Series 8
20133697
TDM: 20089999

===H series ===
20149144
TDM: unknown yet

===J series ===
??
TDM: unknown yet

===K series ===
20165299
TDM: 20089999
== [ TOP Debug Menu ] ==
===Navigation principles===
choosing the number of submenu you get deeper in to chosen submenu. 
If you need change values, usually you will see this:
Input Down(0)/Up(1)/Down100(2)/Up100(3)/Exit(99) > :
Means: 
Every input of '''0''' you get netxt value of this setting. 
Every input of '''1''' shows the value before. 
After the right value is chosen, confirm your selected value with input of '''99'''. This saves setting and exits current submenu.

AFAIK the 2 and 3 make same as 0 and 1.

===Examples===
As example: how to get in to Factory menu (Service menu, but accessible from ExLink cable). 
TV: LE40B653T5W, but on other series the TDM is very similar...

====================================
[ TOP Debug Menu]
------------------------------------
1 : SubSystem Print On/Off
2 : Platform Print Setting
3 : TD Print Setting
4 : Performance Print Setting
5 : Sdal Print Setting
6 : Sdal Trace Setting
10 : Factory Debug
11 : TD Debug
12 : SubSystem DBG
20 : Performance File Write
21 : Louvre Print Setting
22 : JavaMW Print Setting
30 : Auto Lock DBG
------------------------------------
50 : ROSE Debug
60 : MediaLink Debug
70 : Jade Debug
====================================
99 : Exit
====================================
DBG> : 10

====================================
[ SsExeFactoryBase Debug Menu]
------------------------------------
1 : Factory.dat Loading Debug
2 : Hidden Menu Status
3 : GetItem Test
4 : Get SpecialItem Data
5 : Print SpecialItem Number
6 : Each Store Area, Version Clear
7 : Set SpecialItem Data
8 : Default Data Update Test
9 : Display & Excute Factory Menu
====================================
99 : Exit
====================================
DBG> : 9

====================================
[ SsExeFactoryBase Main Menu]
SOURCE_TYPE_DTV1 RESOLUTION_576I
------------------------------------
[0] Option
[1] ADC/WB
[2] Control
[3] SVC
[4] Advanced
[5] FBE3
[6] WB Movie
[7] EPA Standard
[8] CH_VDEC
[9] YC_Delay
[10] AR_ADC
[11] CH_DP
[12] NR
[13] Sharpness
[14] Sharpness_LNA
[15] CE DIMMING
[16] LNA_Plus
[17] Tuner Status
[18] FRC
[19] PQ Others
[20] EEPROM RESET
[21] ...
[22] TC905x7
[23] DDR Margin
====================================
99 : Exit
====================================
Select Menu :2

====================================
[ Control]
SOURCE_TYPE_DTV1 RESOLUTION_576I
------------------------------------
[0] EDID
[1] Sub Option
[2] PDP Option
[3] Hotel Option
[4] Shop Option
[5] Asia Option
[6] SOUND
[7] Config Option
[8] Test Pattern
====================================
99 : Exit
====================================
Select Menu : 7

====================================
[ Config Option]
SOURCE_TYPE_DTV1 RESOLUTION_576I
------------------------------------
[0] Num of ATV
[1] Num of DTV
[2] Num of AV
[3] Num of SVIDEO
[4] Num of COMP
[5] Num of HDMI
[6] Num of PC
[7] Num of SCART
[8] Num of DVI
[9] Num of OPTICAL Link
[10] Num of MEDIA
[11] Num of PANEL KEY
[12] Num of USB Port
[13] MFT Offset
[14] Select LCD/PDP
[15] HDMI/DVI SEL
[16] Indicator Led
[17] Wall Mount
[18] Chelsea HV Flip
[19] Num Of Display
[20] HDMI AV MUTE TIME
[21] DVI/HDMI SOUND
[22] HDMI HOT PLUG
[23] HOTPLUG SWITCHING
[24] HOT PLUG OFF HOLD TIME
[25] HDMI FLT CNT SIG
[26] HDMI FLT CNT LOS
[27] UNSTABLE BAN CNT
[28] HDMI Err Cnt
[29] HDMI ROBIN
[30] HDMI Callback
[31] HDMI CTS Thld
[32] HDMI CTS Cnt1
[33] TMDS_EQ2_Boost
[34] TMDS_EQ2_Gain
[35] TMDS_PLL_Loop
[36] TMDS_CPREG_BLEED
[37] HDMI EQ
[38] HDMI Switch
[39] TTX Group Delay
[40] DVI SET TIME
[41] Woofer_Type
[42] Tuner Lock Count
[43] SIL2165 FW128
====================================
99 : Exit
====================================
Select Menu :

If you need to change some option in service menu, you don`t need to enter this from remote control. Use ExLink instead ;) 
<To be updated>

The K Series Wiki

2016-08-30T17:36:35Z

Szt:

*'''[[Ex-Link Cable for J/K_Series]]'''
*UNDER CONSTRUCTION

To be updated...

The J Series Wiki

2016-08-30T13:35:48Z

Szt: Ex-Link Cable for J/K_Series

Here will be the information about Tizen OS and J series soon.

This is a misc. collection of currently known information. It will be organized better over time.

'''J Series Forum:''' http://forum.samygo.tv/viewforum.php?f=83&sid=bb1391eb2668cb6e2d3c3d793dc557b0

'''Service Menu'''

Be VERY careful once in the service menu. Do not try to navigate using LEFT and RIGHT because that changes values. Only navigate through menu items with UP and DOWN.

With TV powered on (requires remote with FACTORY key): [INFO] [FACTORY] (starts service menu with "Advanced" visible but it has no sub-menu)

With TV powered off: [MUTE] [1] [8] [2] on American models and [INFO] [MENU] [MUTE] [POWER] on European models.

'''Console output'''
*'''[[Ex-Link Cable for J/K_Series]]'''
Ex Link Port - 115,200 N,8,1

RS-232 Jack setting:

UART = no input/output

Debug = system logging output (MUCH more verbose when "Serial Log On/Off" set to ON, which requires a power cycle to take effect)

Logic = no input/output

FANET = no input/output

'''OTN Support Disable (Firmware Upgrades)'''

OTN support cannot be disabled in the service menu. It must be disabled by blocking access to the upgrade servers at the network level.

Ex-Link Cable for J/K/M/Q/N/QN Series

2016-08-30T13:34:24Z

Szt:

== Wired ExLink cable ==
[[File:JU7100-inputs-side-large.jpg|200px|thumb|right|JU7100]]On some J/K-series TV, Ex-Link port is located on the separate 3.5mm jack labelled as "EX-LINK".

In this case, you need to make Ex-link cable by connecting JACK male to the USB-COM adapter(not TTL/LVTTL) as shown below.
[[File:Img.jpg]]

Or you can use regular COM port, if your PC have it, but in this case you have to connect pins in reverse order (from left to right) as shown below. You need 2, 3 and 5 pin.

[[File:Db9-pinout.png]]
== Enable Debug mode in service menu ==
todo
== Start the terminal ==
===Linux PC===
On a Linux PC, install 'cu' (call up) tool from the ''uucp'' package and run
<pre>cu -l /dev/ttyUSB0 -s 115200</pre>
 
===Windows PC===
On Windows, we recommend the free terminal application [http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html Putty] or [http://realterm.sourceforge.net/ RealTerm] ([http://sourceforge.net/projects/realterm/ download]). But [http://www.hilgraeve.com/hyperterminal/ HyperTerminal] is also very nice, but not free.

After you have started PuTTY, follow the steps in the screen shots below. 
[[File:ExLinkPuttySettings1.png|300px]][[File:ExLinkPuttySettings2.png|300px]]
[[File:ExLinkPutty3.png|600px]]

Ex-Link Cable for J/K/M/Q/N/QN Series

2016-08-30T13:29:34Z

Szt: Created page with "== Wired ExLink cable == JU7100On some J/K-series TV, Ex-Link port is located on the separate 3.5mm jack labelled as "E..."

== Wired ExLink cable ==
[[File:JU7100-inputs-side-large.jpg|200px|thumb|right|JU7100]]On some J/K-series TV, Ex-Link port is located on the separate 3.5mm jack labelled as "EX-LINK".

In this case, you need to make Ex-link cable by connecting JACK male to the USB-COM adapter(not TTL/LVTTL) as shown below.
[[File:Img.jpg]]

Or you can use regular COM port, if your PC have it, but in this case you have to connect pins in reverse order (from left to right) as shown below;

[[File:Db9-pinout.png]]
== Enable Debug mode in service menu ==
todo
== Start the terminal ==
===Linux PC===
On a Linux PC, install 'cu' (call up) tool from the ''uucp'' package and run
<pre>cu -l /dev/ttyUSB0 -s 115200</pre>
 
===Windows PC===
On Windows, we recommend the free terminal application [http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html Putty] or [http://realterm.sourceforge.net/ RealTerm] ([http://sourceforge.net/projects/realterm/ download]). But [http://www.hilgraeve.com/hyperterminal/ HyperTerminal] is also very nice, but not free.

After you have started PuTTY, follow the steps in the screen shots below. 
[[File:ExLinkPuttySettings1.png|300px]][[File:ExLinkPuttySettings2.png|300px]]
[[File:ExLinkPutty3.png|600px]]

File:Db9-pinout.png

2016-08-30T13:24:19Z

Szt: DB9 pinout

DB9 pinout

File:JU7100-inputs-side-large.jpg

2016-08-30T12:47:19Z

Szt:

JU7100 exlink

File:JU7100-inputs-side-large.jpg

2016-08-30T12:44:40Z

Szt: Ju7100 exlink

Ju7100 exlink

File:Img.jpg

2016-08-30T12:09:45Z

Szt: Exlink for J/K

Exlink for J/K