Boot from USB using u-boot


From SamyGO
Revision as of 17:06, 30 November 2010 by Juzis28 (talk | contribs) (added manual for root TV over NFS)
Jump to: navigation, search

Note: This instruction apply and booting only to TV with firmwares listed below!

T-CHL5DEUC, T-CHL5DAUC, T-CHE6AUSC, T-CHE7AUSC, T-CHEAUSC, T-CHL7DAUC, T-CHL7DEUC, T-CHU7DAUC, T-CHU7DEUC

This is for advanced users and developers only.


Requirements:

  • Serial connection
  • Usb disk drive or pen drive (at least 256MB)
  • TFTP server outside TV on some host in case using pen drive or optionaly in case disk drive
  • Regular Linux based system to prepare usb disk/pen drive
  • Builded rootfs image

Follow steps:

Build OE kernel and rootfs

Builded rootfs image is located in build-samygo/tmp/deploy/images directory. File name looks like externalboot-base-rootfs-ssdtv-xxxxxxx.tar.gz.

Prepare USB disk

  • Partition usb disk/pen drive.

Partition drive using fdisk or other tool.

First parittion FAT type. It will be usefull or needed if you don't have network on tv. Second partition set as Linux type.

Format first partition with mtools or other tool as VFAT type filesystem. Format second partition with ext2fsprogs as ext3.

  • Unpack rootfs image to linux partition on usb disk/pen drive.

Unpack image to second partition with root rights.

TFTP server for kernel load

  • Put kernel image to TFTP service directory. (or /tftpboot directory. on my NAS it is on /opt/tftpboot)

Note: Do this only if you want faster kernel load image.

  • Find proper kernel image in build-samygo/tmp/deploy/images.

It's like: uImage-2.6.18.8-r0-ssdtv.multi-config-multi-config-bXXX.bin.

For firmwares:

T-CHE7AUSC, T-CHEAUSC, T-CHL7DAUC, T-CHL7DEUC, T-CHU7DAUC, T-CHU7DEUC - use b650

T-CHE6AUSC - use b6000

T-CHL5DEUC, T-CHL5DAUC - use b550

  • Copy and rename it to uImage into root directory of TFTP service or on FAT partition if you are not using TFTP way.
  • Set variables and execute commands in u-boot shell to boot linux kernel.

Booting

TFTP

In case use TFTP set network variables first:

setenv ipaddr 192.168.1.100;setenv gatewayip 192.168.1.1;setenv serverip 192.168.1.200

where first IP is TV, second gateway is not important in this case, third is address of TFTP server.

Boot linux kernel (case TFTP):

setenv bootargs root=/dev/sda2 console=ttyS1;tftp;bootm

USB

Boot linux kernel (case USB FAT partition):

setenv bootargs root=/dev/sda2 rootdelay=1 console=ttyS1;usb start;fatload usb 0 61000000 uImage;bootm

where /dev/sda2 is linux rootfs.

Rootfs over NFS

If you have NFS server on your home network working, you can boot file system for TV (rootfs from OE)over NFS!

Prepare rootfs

  • Attach it to your NFS server
  • Write exports for your USB with rootfs on NAS

Here is an example of my Buffalo NAS:
File to edit is /etc/exports

root@LS-GL984:~# cat /etc/exports
/mnt/usbdisk3 192.168.1.100/255.255.255.0(rw,async,all_squash,anonuid=99,anongid=99,no_subtree_check)

where 192.168.1.100 is my TV IP. 255.255.255.0 is submask, /mnt/usbdisk3 is my USB with TVs filesystem

Boot kernel and rootfs over network

  • Enter to u-boot promt
  • set network variables for NFS (to load kernel)
setenv ipaddr 192.168.1.100;setenv gatewayip 192.168.1.1;setenv serverip 192.168.1.200
  • set network variables for NFS (to load rootfs)
setenv bootargs root=/dev/nfs rw nfsroot=192.168.1.200:/mnt/usbdisk3 rootpath=/home/root ip=192.168.1.102:192.168.1.200:192.168.1.1:255.255.255.0:LS-GL984:eth0:off console=ttyS1

structure of commandline should be:

setenv bootargs root=/dev/nfs rw nfsroot=${serverip} rootpath=${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:eth0:off  console=ttyS1

Where rootpath of OE kernel is /home/root

  • load kernel and start booting TV
tftp;bootm

Starting TV software

After boot system, login over serial console as root and execute followed commands:

  • Install Samsung original software:
samsung-install.sh
  • Start Samsung original software:
samsung-start.sh