Difference between revisions of "Engineering Codes"
(→Arguments of MicomCtrl program) |
m (→Symbol information decode of the exeDSP program) |
||
| Line 7: | Line 7: | ||
* POWER (off) MUTE 1 8 2 POWER (on) -> [[Service Menu]] on older models | * POWER (off) MUTE 1 8 2 POWER (on) -> [[Service Menu]] on older models | ||
* POWER (off) MUTE 8 2 4 POWER (on) -> pin reset | * POWER (off) MUTE 8 2 4 POWER (on) -> pin reset | ||
| − | * MUTE 1 1 9 OK -> " | + | * MUTE 1 1 9 OK -> "HotelMode" |
* MUTE 1 2 0 EXIT -> "LEDDemo" (didn't seem to do anything?) | * MUTE 1 2 0 EXIT -> "LEDDemo" (didn't seem to do anything?) | ||
* MUTE 1 8 4 EXIT -> "DV" | * MUTE 1 8 4 EXIT -> "DV" | ||
| Line 22: | Line 22: | ||
* RETURN for 10 secs -> Internal diagnostics and report | * RETURN for 10 secs -> Internal diagnostics and report | ||
* EXIT for 10 secs -> Factory reset (also TV channels has to be re-tuned) | * EXIT for 10 secs -> Factory reset (also TV channels has to be re-tuned) | ||
| − | |||
== Arguments of MicomCtrl program == | == Arguments of MicomCtrl program == | ||
Latest revision as of 07:01, 17 February 2011
This page lists the available special (undocumented) TV remote key combinations for the TV.
Symbol information decode of the exeDSP program
WARNING! Some of these codes are not tested and may be dangerous.
- POWER (off) INFO MENU MUTE POWER (on) -> Service Menu
- POWER (off) MUTE 1 8 2 POWER (on) -> Service Menu on older models
- POWER (off) MUTE 8 2 4 POWER (on) -> pin reset
- MUTE 1 1 9 OK -> "HotelMode"
- MUTE 1 2 0 EXIT -> "LEDDemo" (didn't seem to do anything?)
- MUTE 1 8 4 EXIT -> "DV"
- MUTE 1 8 5 EXIT -> ?
- MUTE 1 8 7 EXIT -> "DSG" (some HDMI test)
- MUTE 7 3 7 OK -> "PDPFactory"
- MUTE 7 5 0 EXIT -> "FlashPlayerDemo" (goes to content library screen)
- MUTE 9 4 8 EXIT -> "YahooFactoryReset" (resets widgets)
- MUTE OK MUTE OK -> "InfoLinkDemo"
- MUTE ["RSS" key?] -> "ControlPanelVoltage"
- INFO [unknown key with code 0x3B] -> "Factory"
- INFO 3 2 1 EXIT -> "Calibration"
- INFO for 10 secs -> Digital signal quality information
- RETURN for 10 secs -> Internal diagnostics and report
- EXIT for 10 secs -> Factory reset (also TV channels has to be re-tuned)
Arguments of MicomCtrl program
MicomCtrl is a program that responsible about interpreting Remote Controller signal interpretation.
- /mtd_boot/MicomCtrl 18 # for a shutdown
- /mtd_boot/MicomCtrl 22 # for a sync watchdog for exeDSP
- /mtd_boot/MicomCtrl 23 # for a kill watchdog of exeDSP
- /mtd_boot/MicomCtrl 143 # for a reboot
