Dumping and Flashing images by hand


From SamyGO
Revision as of 13:50, 6 December 2009 by Kilroywashere (talk | contribs) (→‎Manual flashing steps)
Jump to: navigation, search

The steps outlined below allow the flashing of an image directly into the flash of your TV, without using the offical upgrade process of the TV.
The example shown below is for flashing a modified exe.img on a UExxB70xx.
There is no need to flash app_data Image, if you are just flashing modifications of the same exeDSP Version.
In any case you need to ensure that you erase the respective flash before overwriting it.

Device files used

Find below the device files for different areas of the firmware for FW types listed ( this information is taken from the run.sh file and was not validated! )

T-CHL5DSEUC, T-CHL5DEUC and T-CHU7DEUC

  • BOOTLOADER_DEVICE=/dev/bml0/2
  • FNW_DEVICE=/dev/bml0/4
  • KERNEL_DEVICE=/dev/bml0/5
  • RFS_DEVICE=/dev/bml0/6
  • BOOT_DEVICE=/dev/bml0/7

T-CHL5DSEUC and T-CHL5DEUC Specific

  • EXE_DEVICE=/dev/stl0/8
  • APPDATA_DEVICE=/dev/stl0/9

T-CHU7DEUC Specific

  • EXE_DEVICE=/dev/bml0/8
  • APPDATA_DEVICE=/dev/bml0/9

For All Devices

  • It's better to conceive the structure of your TV by df tool.

You can check your "df" output. Here is mine on LE40B650T2W which uses T-CHL7DEUC firmware 

# df
Filesystem           1k-blocks      Used Available Use% Mounted on
/dev/tbml6                3136      3136         0 100% /
none                     10240         0     10240   0% /dtv
/dev/tbml7                1024      1024         0 100% /mtd_boot
none                     10240         0     10240   0% /mtd_ram
/dev/stl0/14             11224      1778      9446  16% /mtd_rwarea
/dev/tbml10              61400     52440      8960  85% /mtd_exe
/dev/tbml11              29312     29312         0 100% /mtd_appdata
/dev/stl0/13            193536    160000     33536  83% /mtd_tlib
/dev/stl0/15             51160      1976     49184   4% /mtd_contents
/dev/stl0/16             90012     16344     73668  18% /mtd_down
/dev/stl0/12            152576       224    152352   0% /mtd_wiselink
/dev/stl0/17             89072       176     88896   0% /mtd_swu

Interpretation of this list is like that:

As you can easily understand mount of /mtd_exe means EXE_DEVICE is that /dev/tbml10.

And / describes that is ROOT device at /dev/tbml6.

  • EXE_DEVICE = /dev/tbml10
  • ROOT_DEVICE = /dev/tbml6
  • APPDATA_DEVICE = /dev/tbml11
  • BOOT_DEVICE = /dev/tbml7

You have to aware that, there is some devices not shown on df commands like bootloader or like kernel devices...

Manual flashing steps

  • (1) Prevent TV from rebooting when exeDSP is stopped
/mtd_boot/MicomCtrl 23
  • (2) Stop exeDSP binary
killall -9 exeDSP
  • (3) Unmount the respective directory
umount /mtd_exe
  • (4) Take a backup of the current image in the flash.
bml.dump /dev/bml0/8 /mtd_swu/exe.img.orig

If you dont have bml.dump tool in your firmware, than you can use dd or cat tool too. 

cat /dev/bml0/8 > /mtd_swu/exe.img.orig

dd if=/dev/bml0/8 of=/mtd_swu/exe.img.orig
  • (5) Move backup image to a safe space ( e.g. USB )
mv /mtd_swu/exe.img.orig /dtv/usb/sda1
  • (6) Copy Image to be flashed from your USB to /mtd_swu
cp /dtv/usb/sda1/exe.img /mtd_swu

-> this is the safest way, even though flashing directly from USB-Device may also be possible, which I have not tested

  • (7) Erase the flash before flashing the new file
bml.erase /dev/bml0/8
  • (8) Perform the actual step of flashing the file.
bml.restore /dev/bml0/8 /mtd_swu/exe.img

->Flashing progress will be shown 0% ... 100%. Don't interrupt this process!!

  • (9) Mount the updated image( afterwards check out content and ensure it mounts without problems and looks ok from a content perspective. )
mount -t auto /dev/tbml8 /mtd_exe
  • (10) Starting exeDSP
/mtd_exe/rc.local

-> If something went wrong and your exeDSP doesn't start up properly, then you can flash back your backup ".orig" image following steps 3-9.
-> Don't worry, if you see your screen upside down after re-starting exeDSP ;-) as the exeDSP binary seems to expect a freshly initialized HW to start-up properly



Attention:This process does not validate the correctness and validity of the file being flashed. THIS IS YOUR RESPONSIBILITY!!!

--Dynamic1969 17:59, 3 October 2009 (UTC)

Retrieved from "http://wiki.samygo.tv/index.php?title=Dumping_and_Flashing_images_by_hand&oldid=251"