Difference between revisions of "How to send FACTORY+3SPEED keys"


From SamyGO
Jump to: navigation, search
m (Ready to use .wav files)
Line 20: Line 20:
 
The connections should be as showed below= Led1 (+) must be connected to Led2 (-) and Led1 (-), Led2 (+) must be connected to the 2 stereo channels leaving the ground not connected  
 
The connections should be as showed below= Led1 (+) must be connected to Led2 (-) and Led1 (-), Led2 (+) must be connected to the 2 stereo channels leaving the ground not connected  
  
[[File:Picture2.png|400px]]
+
[[File:Immagine10.png|400px]]
  
 
Using the stereo jack+2Led's and having the needed audio .wav files corresponding to the needed RC key code, it is possible to emulate the RC by inserting the jack in a common .wav player and put in play the audio files
 
Using the stereo jack+2Led's and having the needed audio .wav files corresponding to the needed RC key code, it is possible to emulate the RC by inserting the jack in a common .wav player and put in play the audio files

Revision as of 19:39, 5 July 2012

This page has the goal to show an alternative procedure for sending IR codes to Samsung TV. The procedure has successfully been used for unlocking the Local Area setting available on Service Menu (UE46EH5000) and set the correct one (by sending FACTORY and 3SPEED). In this way I could get a TV 100% compliant to my country (it was bought in another one).

Theory

The process is based on the fact that the IR key codes are series of square waves at 38kHz of main frequency. The duration in time of the square waves ON and OFF defines the codification of a specific key. By considering a common audio stereo channel (2 mono), it can support max of 22kHz per channel with a total of 44kHz. This means that if an audio stereo channel is created by considering 2 mono channels defined in this way:

- Channel #1= sine wave with 19kHz as main frequency and silent for the time duration at which original IR key square wave is zero

- Channel #2= same as Channel #1 but inverted (basically mirrored)

then, it is possible to emulate the Remote Controller with a simple audio player hardware and a very simple dual led transmitter.

How to build the dual led IR transmitter

What you need is:

- 2 IR Led 940nm 5mm (the typical one present on RC)

- 1 stereo jack 3.5mm

The connections should be as showed below= Led1 (+) must be connected to Led2 (-) and Led1 (-), Led2 (+) must be connected to the 2 stereo channels leaving the ground not connected

Immagine10.png

Using the stereo jack+2Led's and having the needed audio .wav files corresponding to the needed RC key code, it is possible to emulate the RC by inserting the jack in a common .wav player and put in play the audio files

Ready to use .wav files

Curently just two codes (required to unlock locked service menu settings) are prepared:

FACTORY
3SPEED

You can download them from SamyGO download area. Direct link here.
Another usefull codes...

POWER ON/OFF
CH UP/DOWN

... will be uploaded later.

Important Notes

1. The sound player hardware should have stereo output with enough amplification (I tested on 3 smartphones and it worked only on Nokia N8). It shouldn't be a problem if PC sound card is used

2. The output Volume must be set to maximum level

3. The distance of action (from TV receiver) depends on output amplification (it can be 20cm or 3-4m)

4. The 2 Led must be correctly positioned in order to have enough area where the 38kHz are obtained as sum of the 2x19kHz (see below)

Picture3.png

Following some pictures of my IR transmitter based on audio .wav
Picture4.jpgPicture5.jpgPicture6.jpg

References

  • This the link I used as reference for the process [1]
  • Related topic.




pdca 19:20, 5 July 2012 (UTC)