Difference between revisions of "Main Page"
m (→Welcome to SamyGo WiKi) |
(create a dedicated page for compatibility so we can go into a lot of detail) |
||
| Line 9: | Line 9: | ||
== Compatibility Overview == | == Compatibility Overview == | ||
| − | + | ||
| − | + | See the [[Compatibility]] page to see which TV models should work. | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
== Safety Measures ( which you shouldn't start without ) == | == Safety Measures ( which you shouldn't start without ) == | ||
| − | #Have a working Ex-Link cable at hand. | + | #Have a working [[Enable Serial Console on non CI+ Devices|Ex-Link cable]] at hand. |
#Ensure the backup exe.img ( stored on /dev/tbml10 ) is in good condition ( and ideally not altered. ) | #Ensure the backup exe.img ( stored on /dev/tbml10 ) is in good condition ( and ideally not altered. ) | ||
#Ensure your RS232 Setting in the Service-Menu is set to "debug". | #Ensure your RS232 Setting in the Service-Menu is set to "debug". | ||
Revision as of 14:03, 7 December 2009
Contents
Welcome to SamyGo WiKi
Unfortunately, SourceForge doesn't allow users to write on wiki. We needed to assign writing permission by hand.
First you needed to give a vote "thumb up" for this idea for make SourceForge to allow all users has write access to wiki.
After After you can place note for editing permissions by hand on request from forum (Drop message to Erdem_ua or dynamic1969).
Compatibility Overview
See the Compatibility page to see which TV models should work.
Safety Measures ( which you shouldn't start without )
- Have a working Ex-Link cable at hand.
- Ensure the backup exe.img ( stored on /dev/tbml10 ) is in good condition ( and ideally not altered. )
- Ensure your RS232 Setting in the Service-Menu is set to "debug".
- Know that your TV will reset RS232 jack back to UART mode after new firmware installation or reverting back to old version.
Useful WIKI articles
Firmware Modification
- How to enable Telnet on samsung TV's
- How to enable Telnet/NFS/CIFS/SAMBA
- Enable Serial Console on non CI+ Devices
- Getting access to uBoot / bootloader
- Dumping and Flashing images by hand
- Open backdoor for fixing bootloop situations
- Mounting an NFS share on a USB device to bypass DLNA
- Mounting an CIFS/SAMBA share on a USB device to bypass DLNA
Software Tools
- Setting up a native-compilation toolchain
- Setting up a cross-compilation toolchain
- SamyGO Extensions Pack
- SamyGO ChanEdit - Chanel Editor
General Information
Interesting Reference Material
The file-system used in the the recent Samsung TVs is "RFS". Its proprietary nature and consequently so the absence of an according Linux RFS-Module in the standard Linux distributions makes it currently impossible to modify files by simply mounting the respective image as "RW", modifying it and saving the respective image again. This is the reason why currently all changes are done via patching of the image-binaries.
The information provided here should help, that we get a RFS module compiled for our common Linux distributions
--Dynamic1969 19:24, 6 October 2009 (UTC)
Disclaimer
Neither this WIKI/Forum nor the author(s) of articles and information provided accept any responsibility for damage that may be caused by use of the information provided. You do everything at your own risk. Be aware that "hacking" activities do void your warranty!
Tested on UExxB70xx, LExxB65x and compatible devices only.
